AUTOOL Automatic Brake Bleeder Kit Pulse Brake Fluid Bleeder Exchanger Machine

Description: Why Do We Need to Exchange Car Brake Fluid? After being used for a period of time, automotive brake fluid will have a lower boiling point, pollution and oxidative deterioration, which will affect the brake performance and cause safety hazards. Also, the brake fluid reservoir has a vent, which causes the brake fluid to draw in moisture from the air and turn into air bubbles at high temperatures. When air bubbles appear in the brake fluid pipeline, there will be a loss of braking power or brake failure. Therefore, it is necessary to check the quality performance of the brake fluid according to the operating environment, seasonal changes and working condition, and to exchange it on time. Generally, brake fluid should be exchanged after two years of use or 50,000 km. 【Built-in Air Pump】 No need to connect an air compressor. AST605 brake system bleeding tools comes with a built-in working pressure pump. Brake fluid can be exchanged by simply connecting 110V/220V power supply 【Pressure Adjustable】 AST605 adjustable pressure range is 0.6-3.0bar, the brake pressure bleeder kit is equipped with an adjustable pressure button and a pressure gauge, you can monitor the pressure in the container at any time.it enables you to customize the pressure level based on the specific requirements of the vehicle. By increasing the pressure, you can accelerate the speed of the operation, which makes it possible to cater to various demands in diverse situations. 【Efficient and Time Saving】 Equipped with 1.5L waste oil bottle,Output Flow ≤1.5L/min,It changes the traditional way of exchanging the brake fluid by 2 people. One person can easily exchange the brake fluid in just 4-10 minutes,, which will save you a lot of time and labor costs, but also this pulsating brake fluid exchanger can effectively avoid the generation of air bubbles during the filling process, thereby optimizing or avoiding the artificial exhaust process 【Kindly Note】 Wear safety goggles to minimize the risk of injury from splashing.Wear suitable, protective gloves to minimize the risk of injury caused by skin contact.Evacuate at first startup. Drain the old brake fluid until new brake fluid comes out. 【Three Years Warranty】 For the damage caused by non-human factors, AUTOOL promises to resend the parts for free within 3 years. For any demand, we warmly welcome you to contact us, and we will reply you as soon as possible within 24 hours. Instruction of AUTOOL AST 605 Brake Fluid Exchanger 1. Lift the car to the right height to suspend the wheels off the ground. 2. Connect the four oil bottles of the equipment to the car brake sub-cylinders, and loosen the outlet screw of the brake sub-cylinders to ensure that fluid can be flown out. 3. Put the inlet hose and pressure adjustment hose into the new brake fluid bottle 4. Connect the power supply and turn on the power switch. 5. Press the Start button to build up the pressure until the pointer of the pressure gauge exceeds 1 bar. At this time, you can release the button and adjust the pressure as needed. 6. Before replacing the brake fluid, the output hose must be exhausted first, and then find the matching model connector and connect it to the oil reservoir of the brake master cylinder. 7. During the fluid exchange, if the exchanging speed is a bit slow, the output pressure can be adjusted appropriately as required. 8. After the fluid exchange is completed, please turn off the machine and reduce the pressure to zero, then remove the connector attached to the car reservoir to prevent the excess pressure from causing an overflow of the brake fluid. Precautions Do not mix DOT5 with DOT3 and DOT4 because the base oil composition differs. The bleeding sequence during fluid exchange needs to follow the principle of "far to near from the master cylinder or brake pedal". For left-hand drive vehicles, the order is "right rear wheel → left rear wheel → right front wheel → left front wheel", bleeding, in turn, to ensure that the discharge of clean fluid and no air bubbles. Please do not start driving immediately after the brake fluid exchange is completed, it needs to be checked to make sure there are no leaks in the pipeline. Start the vehicle, keep it idling in place and press the brake pedal to ensure that the pedal resistance gradually increases and that the brake fluid pressure is maintained. Then perform an internal road test to confirm that the braking performance is normal before driving on the road. Packing List 1pc*AUTOOL AS605 brake fluid bleeder exchanger main unit 1pc*User Manual 1pc*Certificate 1pc* Fluid recycling bottle(1.5 L)

Price: 299.99 USD

Location: shenzhen

End Time: 2024-08-10T08:29:07.000Z

Shipping Cost: 0 USD